Short press the power button Power, the No.1 indicator light will stay on, the 2.3.4.5 indicator lights will flash, and after 3 seconds, they will all turn off.
Press and hold the power button for 3 seconds. After the first indicator light goes out, the device has been turned off.
- REMOTE CONTROL AUTOMATIC SHUTDOWN:
The remote control is not connected to the scooter, and it will automatically shut down after 30 seconds. If the remote control is connected to the scooter, it will not shut down automatically. You must wait for the scooter to shut down after it has been disconnected for 30 seconds before shutting it down.
Firstly, turn on the power of the scooter, then press and hold the scooter power button for 3 seconds. After the scooter indicator light flashes once every 0.5 seconds, the scooter enters pairing mode. Then turn on the power of the remote control. There is a hidden button on the back of the remote control. Use a long needle to poke the "pairing button" into the small hole and press it once to release it. Do not hold it down for a long time, it will be released in a short time. The first light on the remote control will flash, and the scooter power indicator light will flash once. At this time, pairing is successful and the scooter can be used. Note: Long press the power button on the scooter, short press the remote control.
- SCOOTER BATTERY INDICATOR:
The remote control has successfully connected to the scooter and is ready for use. The 2, 3, 4, and 5 indicator lights indicate the scooter's battery level. The 2nd light has a battery level of "100% -75%", the 3rd light has a battery level of "75% -50%", the 4th light has a battery level of "50% -25%", and the 5th light has a battery level of "25% -5%". If the battery level is below "10% -0%", the 5th indicator light will flash for 0.5 seconds.
- REMOTE CONTROL BATTERY INDICATOR:
Within 3 seconds of turning on the remote control, the lights 2, 3, 4, and 5 will flash to indicate the remote control's battery level. Follow the instructions for (light 2 "100% -75%"), (light 3 "75% -50%"), (light 4 "50% -25%"), and (light 5 "25% -5%") battery levels.
Display the remote control battery level, and when the remote control battery level is below 20%, the 6th indicator light will flash for 0.5 seconds.
Push the "roller" forward to control the skateboard's movement, and pull the "roller" backward to control the skateboard's braking.
Pushing the 'roller' forward can switch the speed gear by pressing the button, and pulling the 'roller' backward can switch the brake force adjustment.
- SCOOTER DIRECTION SWITCHING:
The scooter is in a stationary state. Press and hold the Reverse button for 3 seconds to switch the front and rear directions of the scooter. When the scooter travels in the forward direction, the first light displays green. Press the Reverse button again briefly to move the scooter backward, and the first light displays red. Repeat the front and rear directions in sequence, and the first light displays green/red.
- SCOOTER SPEED GEAR SWITCHING:
When the scooter is in a stationary state or in a sliding state, press the Power button briefly to switch between the four gears of the scooter. The 5th light of the first gear is always on, the 4th light of the second gear is always on, the 3rd light of the third gear is always on, and the 2nd light of the fourth gear is always on. After successfully switching for 3 seconds, exit. Note that in each gear and when each light is always on, the other 3 lights are not on. Note: First gear is low speed gear, second gear is medium speed gear, third gear is high speed economy gear, and fourth gear is sport player violence gear.
- SCOOTER BRAKE FORCE GEAR SWITCHING:
Pull the "scroll wheel" backwards on the remote control without releasing it, and press the Power button briefly to switch the brake force of the scooter to four gears. The 5th gear light flashes in one gear, the 4th gear light flashes in the second gear, the 3rd gear light flashes in the third gear, and the 2nd gear light flashes in the fourth gear. Note: Other lights do not light up when each gear and light is flashing.
When the signal is lost, if the remote control is in acceleration mode, the scooter stops accelerating and the motor slides freely. When the scooter is in braking mode, the signal is lost and the brake is still effective within 1 second. It can be reconnected within 1 second and can continue to be used. If the signal is lost for more than 1 second, the brake will fail and the skateboard will slide freely.
The remote control is charged with Micro USB. After connecting the remote control for charging, the 2.3.4.5 indicator lights on the remote control quickly flash and move. All four lights remain on to indicate that the remote control is fully charged. During charging, the 6th light remains on, which is the charging indicator light.
- REMOTE CONTROL BATTERY PROTECTION:
When the battery level of the remote control is below 20%, the 6th light flashes. When the battery voltage is below 5%, pushing the "roller" forward is prohibited, and pulling the "roller" backward brakes normally. If the remote control battery level is below 1% and the voltage is 3.0V, the remote control will automatically shut down.
Note: When the battery level of the remote control is below 20% and the 6th indicator light flashes, it is best for the user to charge the remote control in a timely manner to avoid damage to the lithium battery due to overdischarging.
