Your cart is empty.
Your cart is empty.
COMPATIBLE
Key Switch Ignition 6 Wire replaces for Mercury part number: 87-88107 , 87-88107A5, 7-1155.
Boat Ignition Switch with Key 6 Wire fits for most Mercury Outboard Motors 1994 and Later using.
WIDELY USE
- Works perfect on 225hp Merc&2020 bass tracker classic XL turns over and starts better than ever.
- The boat ignition switch with key was exactly what you needed for your 2012 mercury 90 outboard.
- Boat ignition switch with key 6 wire replaced ignition switch on your Bentley pontoon boat with mercury 50 hp 4 stroke Bigfoot all wires matched was a snap to install.
- Boat ignition switch worked perfect as a replacement for your bass buggy 40hp.
- Perfect fit for your Mako skiff 17/ colors and push key match original Mako/ Tracker original.
- Used boat key switch with choke on a 1982 Mercury and worked perfectly.
FEATURES
Wires color coded for easy, correct replacement. Well made with epoxy filled and sealed wires to make water proof and provide strain relief on wires exiting switch body.
This boat ignition key has similar build quality as the OEM switch that I replaced, the color coded wires match as you would hope, and the switch works great.
EASY TO INSTALL
Colors on switch wires match factory color codes. Push to choke ignition switch was easy to install, direct replacement, just match up color of wires and then install.
DESCRIPTION
Boat Ignition Switch with Key 6 Wire Positions: Off - Ignition - Start, includes 2 keys
Boat Ignition Switch with Choke rated Up to 30 amps 12V
Boat Ignition Switch with Key Face Nut: Hex black plastic
Ignition Switch Boat Push to Choke 6 Wire Base Terminal Type: Six color-coded wire leads/potted
stormrider154
Reviewed in the United States on May 5, 2025
Switch was exactly as advertisedPlus it arrived a day early
JoeC fishing
Reviewed in the United States on August 4, 2024
Switch seems well built ,not cheap thin plastic same for keys they seem like you won't bend them over. easy to connect factory harness to, just match up colors then you just plug it up.it works for my 2018 Ranger rt198p looks like it came from the factory
Murray
Reviewed in Canada on August 26, 2024
This ignition harness is colour-coded and easy to install. Works like a charm, including the choke.
Aidan Smith
Reviewed in the United States on August 15, 2024
Had it installed for about a month. One day went to start the boat and the ignition was hard to turn. On the way back in started the boat about a mile back started smelling burning and the starter was still engaged and the wires got hot melted others then fire under the center console and yea just floating. Don't recommend this ignition.
Alan Able
Reviewed in Canada on August 14, 2024
The price was right and delivery was very fast.Be careful with the wiring to make sure that you match the original ones. All matched except the blue wire from my Mercury Marine 4 stroke matched the yellow/black wire. I made a chart and then used a circuit tester to confirm which one was which.My push in choke setting was sticky and this replacement fixed it.
Todd Austin
Reviewed in the United States on July 2, 2024
I installed this in an aluminum boat. There are no wiring instructions included, so one has to copy them from the Amazon web page. Also, there is only one mounting nut to hole the switch to the dash. As my boat is aluminum, it is thin. This makes the switch protrude quite a bit from the dash. Unsightly. It would be much better if another nut were included to fix this issue. The switch seems to function fine and overall I am pleased.
TaosDude
Reviewed in the United States on June 22, 2024
Replacement for Mercury 150 HP ignition switch. Fit perfectly, wired right up, easy install and still working after couple of months use.
Lisa D
Reviewed in Canada on November 29, 2024
Worked great on my 24ft pontoon boat ignition
SAM the hammer
Reviewed in the United States on October 24, 2024
Direct replacement for the switch I had, worked as it should
Weim_Momma
Reviewed in the United States on April 20, 2023
This unit was purchased to replace the failing ignition switch on a Mercury equipped outboard. The failing switch was experiencing issues with the stator internal switch where it would work when inverted but not in mounted position.The new switch came packaged well and uses industry standard wire coloring. This made installation extremely easy as it matches the wires on the boat already. Simply attaching connectors to the ends and hooked up to the harness. It has worked flawlessly during testing and also while on the water since install.
Customer
Reviewed in the United States on March 23, 2022
It installed fairly easy it is a little larger and diameter than the original switch the color codes did line up with mine but the key has no tumblers on it and likes to fall out of the ignition switch otherwise than that it does work
Recommended Products
