Shopping Cart

Your cart is empty.

Your cart is empty.

ABS Wheel Speed Sensor - Front Rear Left Driver and Right Passenger Side ABS Wheel Speed Sensor Compatible for Jeep Wrangler 3.6L 2007-2017 Jeep Wrangler 3.8L 2007-2011 68003281AA

Free shipping on orders over $29.99

$22.99

$ 9 .99 $9.99

In Stock

About this item

  • Fitment - For Jeep Wrangler 3.6L 2012-2017/For Jeep Wrangler 3.8L 2007-2011. PANNUOSCS speed sensor can keep the direction stability of the car when braking as much as possible. When the driver presses the brake pedal quickly in emergency braking, the front wheel will not be locked and the steering ability still exists,avoiding the danger in front when braking
  • Replacement Part Number - Front ABS Wheel Speed Sensor (Left,right):68003281AD/68003281AA/68003281AB/68003281AC/52060156AD. Rear ABS Wheel Speed Sensor (Left,right): 52125003AD/52125003AB/52125003AC
  • Direct Replacement - This ABS Wheel Speed Sensor is designed to match OE units in fit, form, and function for peak performance, 2 pins terminal connector for plug and play design, easy to install, no wire splicing necessary, direct replacement for a proper fit every time.
  • Trustworthy Quality - This part is manufactured to exacting standards to ensure reliable performance and durability, the sensors are constructed of high quality material to ensure trouble-free performance and long service life, every component has undergone complete quality control throughout the manufacturing process.
  • PANNUOSCS speed sensor can keep the direction stability of the car when braking as much as possible. When the driver presses the brake pedal quickly in emergency braking, the front wheel will not be locked and the steering ability still exists,avoiding the danger in front when braking



Product Description

68003281AA
68003281AA

Installation Steps:

Step 1: Prepare a jack, an internal hexagonal screw driver, and remove the tire.Also note that there is a small steel wire hook with a ring in the vehicle tools.lt is the size of a common key, which is used to remove the wheel mark. Afterthe tire is removed, it can be easily removed from the inside to the top.
Step 2: The 10 o'clock position on the outer part of the wheel bearing.
Step 3: Find the T30 and ABS sensor fixing screws, and use tools to remove the screws.
Step 4: After removing the screws, shake them a little before pulling them out.A lot of dirt and dust needs to be cleaned up.
Step 5: Pull out the ABS sensor and interface. There is only one snap at the interface.
Step 6: This mounting position can be inserted directly into the large hole.The original dust and mud can be flushed directly withwater, and will not accumulate!
Step 7: lf the height of the ABS transmitter is a little different and the card is not in place, just use a knife to cut the front! Finally,use T30 screws to fix the ABS sensor and mount the tire.

Customer
Reviewed in the United States on January 11, 2025
I thought the issue with my Jeep Wrangler was a bad speed sensor, so I ordered these to swap the bad one out. I also ordered a scan tool to figure out which one was bad as the odds of all four going bad at once are very slim. Once I hooked the scan tool up, I found out my ABS module was bad, not the speed sensor, so I didn't actually use these as planned. As the speed sensors do go out routinely, I held on to these as they look just like the stock parts and seem well built. I can cut my Jeeps downtime since I have spare parts on hand, which is always good, especially with Wranglers.
Vincent L.
Reviewed in the United States on September 24, 2024
Exact replacement
BurningMan0726
Reviewed in the United States on June 18, 2024
Only received half of what was paid for. 1 front, 1 rear.
John and Audrey
Reviewed in the United States on October 18, 2024
Bought these to replace all 4 ABS sensors because I was getting a sensor code, shoulda know, what were the odd’s all 4 were bad, only to find out the ABS module was defective. In the meantime, never got round to installing these. That said, they look exactly like the ones I needed. Part fasteners included. Just didn’t end up using them.
Nikkie
Reviewed in the United States on October 10, 2024
Replaced my sensors after one got damaged. Unfortunately both the rear sensors are bad and throwing codes like crazy. Having the bad sensors on is causing my ABS, traction control light and brake lights to be active on the dash and causing the traction control to randomly kick on.
Recommended Products