Shopping Cart

Your cart is empty.

Your cart is empty.

Accusize Industrial Tools 5C 5'' Collet Chuck with Integral D1-3 Camlock Mounting, 9/16'' Stud, 0269-0013

5.0 (3) Write Review
Free shipping on orders over $29.99

$449.00

$ 99 .00 $99.00

In Stock

1.NumberofItems:1


About this item

  • Outside Diameter: 5". Max. RPM 6000. Accuracy: .0006 TIR. Weight: 10.44 lbs. Spindle: D1-3. No. of Stud: 3.
  • Itegrated D1-3 back mounting. Install on the machine in seconds, no machining required.
  • Can be used on any lathe with D1-3 cam lock mounting
  • Can use any size 5C Collet: Round collet :1/16 ~ 1-1/8"; Hex collet:1/8" ~ 7/8"; Square Collet:1/8" ~ 3/4"
  • Scroll and pinion design just like 3-jaw chuck, operated with chuck key. Scroll & pinion precision machined and hardened.
  • Integrated D1-3 Camlock Mounting: Easy and quick installation on lathes with D1-3 cam lock, eliminating the need for additional machining.
  • Universal 5C Collet Compatibility: Accepts round collets from 1/16" to 1-1/8", hex collets from 1/8" to 7/8", and square collets from 1/8" to 3/4".
  • Exceptional Precision: Offers a TIR (Total Indicator Reading) of 0.0006", ensuring high accuracy in machining tasks.
  • Robust Design: Features a scroll and pinion mechanism hardened for durability, akin to a 3-jaw chuck, with a max RPM of 6000.
  • Ready-to-Use: Comes fully assembled with a 9/16" stud, weighing 10.44 lbs, for immediate use upon receipt without additional setup.


Product Description

AccusizeTools - 5C 5" Collet Chuck with Integral D1-3 CAMLOCK Mounting, Stud = 9/16", 0269-0013

  • Please don't buy this item unless you are familiar with this type of product. Thanks.
  • Outside Diameter:  5"
  • Integrated D1-3 back mounting. Install on the machine in seconds, no machining required
  • Can be used on any lathe with D1-3 cam lock mounting
  • Customers don't need to do any work when received, just mount it on your machine spindle and go.
  • TIR: 0.0006"
  • Spindle: D1-3
  • No. of Stud: 3
  • Diameter of Stud: 9/16"
  • Weight: 10.44 lbs
  • Can use any size 5C collet; Round collet :1/16 ~ 1-1/8"; Hex collet:1/8" ~ 7/8"; Square collet:1/8" ~ 3/4"
  • Scroll and pinion design just like 3-jaw chuck, operated with chuck key
  • Scroll & pinion precision machined and hardened
  • Max. RPM 6000
0269-0013

NOTE

Please note that you need to confirm the taper of your lathe using this 5C collet chuck is 14°15' before you place an order. Otherwise, the run-out will not be accurate at all. Please don't buy the chuck unless the taper of your lathe is exactly 14°15'. Usually, when a lathe has been running for a few years, its taper becomes not as accurate as a new lathe, which causes inaccurate run-out when operating the 5C collet chuck.

The method of measuring the 0269-5C Collet Chucks: Step 1

  • Check the runout of lathe spindle first. Adjust the runout value of nose within 0.004mm; of cylinder or taper within 0.004mm shown as left.

The method of measuring the 0269-5C Collet Chucks: Step 2

  • Then put the 5C chuck onto the lathe spindle nose, with the setting hole at the right position to fix each other (While measuring, we used the screw lock device shown in picture-1. We did not have cam lock device shown in picture-2. They work theoretically the same, by different methods.)

The method of measuring the 0269-5C Collet Chucks: Step 3 and Step 4

  • After putting the 5C fixture into the measuring equipment, enable the screw lock or the cam lock to work with the chuck on the measuring equipment. Please be noticed to tighten the cam screws in multiple strokes crossly.
 
  • Approach the surface of the taper hole with a micron indicator; then rotate the measuring equipment slightly. Reading and noting the micrometer’s value. Tighten the one or two cam screws to correct the 5C fixture, until the runout value within 0.006mm.

The method of measuring the 0269-5C Collet Chucks: Step 5

  • Applying the standard 5C measuring bar, use two lock gears to tighten it slightly. And assure the run-out of the 5C fixture orifice, 0.015mm.

Mary S.
Reviewed in the United States on May 3, 2024
This adaptor does not match the spec's for D1-3 spindle mount, tapered hole is too small, adaptor didn't seat flush. Poor workmanship. Returned for credit!
Joseph A McClain
Reviewed in the United States on January 30, 2018
More than .002 inches of runout, as compared to the .0006 advertised. I can get better repeatability with the 3-jaw scroll chuck. Still useful for things like very small or threaded stock, but not for anything where concentricity matters. Measurement carried out on the spindle as described in the product description, and I also just put a half-thou indicator on the taper without a collet installed. Same result.To check further, I mounted it between centers on a freshly turned arbor, after making sure tailstock alignment was good. The back mounting surface is both flat and square to the axis, but the bore is off center.
Adam M.
Reviewed in the United States on July 31, 2017
Can't beat the price. Plenty good for what I need