Your cart is empty.
Your cart is empty.Backed by superior materials and rigorous testing, MOOG hub assemblies deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.
Customer
Reviewed in the United States on February 18, 2025
Great product.
Toms
Reviewed in the United States on April 12, 2025
So far so good. Fairly easy insulation on jeep wrangler. Hard part in getting old one off if on for 15 years.
TechDave
Reviewed in the United States on August 5, 2024
Great price. Fast shipping. Exactly as described.
Dirt squirt
Reviewed in the United States on June 15, 2024
Fit our 2009 Wrangler perfectly.
Raj
Reviewed in the United States on March 18, 2024
I was a little skeptical @ 1st, thought I would be getting a knock off part. I received the part, opened the box.... It was the item described, awesome! Installed the part with no issues. The wheel speed sensor was a bit short (most likely OEM specs), so i reused the dorman wheel speed sensor already installed on vehicle.So far, happy with part and overall purchase.
Max the ax
Reviewed in the United States on March 10, 2024
My old bearing started to go out at 190K miles. Was able to move the wheel about 1/4" back and forth with the old bearing. Now everything is tight like new. I recommend also buying new bolts when replacing this. Old hub wah hard to get out (rust and dirt) but new hub went in easy after cleaning everything up. Good U-tube vids on how to do the work are available.
Andre Baril
Reviewed in Canada on May 30, 2023
Nice good quality part, made by MOOG, good price too... ABS sensor wire is a bit too short, I had to reroute it.
Speartip
Reviewed in Canada on May 25, 2023
Removing the old hub was biggest challenge . A few light taps with hand held sludge hammer loosened off old hub .New Hub went on with no issues .Replaced stock 12 point head bolts with Dorman 5 point head bolts.Tightened up ride in a good way so old bearings were worn .ABS sensor wire is the same as stock .37 1/4 “.
Soh
Reviewed in Canada on October 19, 2023
Needed a new hub assembly for my axle swap project.The biggest challenge was removing the old hub assembly I ended up using a heavy hummer and it worked. The ABS sensor and wire are both the perfect length for Jeep Wrangler JK 2010. Take your time to hook up the sensor, which is just the back side of the front shock.I drove only ~2,000 km after installation, so will see how long it lasts. If you replace the wheel hub assembly, I would highly recommend replacing a set of ball joints and axle u-joints as well.
nathan hansen
Reviewed in the United States on September 6, 2022
The moog hub bearing is a nice unit. I replaced both sides on my 2010 jku. I finished in about 4 hours. Granted I fought a froze axle in the driver side and had to do some deleting. Overall should have taken about 2-1/2hrs I’d say. Tools needed. 12 point 13mm socket. 21mm socket or wrench 36mm socket for spindle nut, wire brush( I used a grinder and wire wheel) small screwdriver. Pretty simple job.
RickH
Reviewed in Canada on March 26, 2022
Factory fit at a discounted price.
James McKee
Reviewed in the United States on February 21, 2022
Many of the reviews on this wheel hub where correct about the length of the speed sensor wire. If you have a lifted Jeep JK (mine has a 4 inch lift) and plan to change out the speed sensor wires when you install the new wheel hubs, make sure you buy extra long speed sensor wires separately. There was about a 8 to 9 inch difference between the wire that comes with the wheel hub and what I needed for my lifted Jeep. Other than that the instal went without a hitch. Hope this is helpful!
Brad
Reviewed in Canada on June 24, 2019
Installed on pass side of a 2007 Jeep unlimited with a 3.5” lift. Wires were same length as factory. It is a Moog product but made in Korea. Quality product.
Recommended Products
