Your cart is empty.
Your cart is empty. SEA-DOO SOLAS IMPELLER W/ IMPELLER TOOL WEAR RING
Includes Solas Impeller, Impeller Tool Aftermarket Wear Ring
11/19 Pitch for use on mostly stock engines
Increases low end, acceleration and adds+1-2MPH
Made from high strength corrosion resistant stainless steel
Direct replacement, no modifications required to install
Exact item pictured
Part Number:
Solas Impeller SR-CD-11/19
Solas Impeller Tool WR011
Wear Ring 267-000-104/ 267-000-419/ 267-000-021/ 267-001-236
Fits: SeaDoo
GTX 155 2004-2008
GTX Wake 155 2004-2006
Wake 155 2008
RXP 155 2007-2008
Islandia SE 2007
GTI/ GTI STD./ GTI SE 130 2006-2019(Modified Only)
GTI Ltd. 155/ GTI SE 155 2008-2019(Modified Only)
Robert D.
Reviewed in the United States on August 22, 2021
excellent quality, fits and works great
va scott 47
Reviewed in the United States on June 11, 2021
Replaced wear ring and impeller on a 2015 Sea Doo Wake 155 after picking up a rock. Parts fit perfectly.Only minor complaint is about the tool, which is a little short. It's long enough to get the job done, but another 1/2-1 inch would be helpful when clamping it in the vise with the rubber boot already installed.
Stephanie Maggs
Reviewed in the United States on April 17, 2021
The package didn’t have a a impeller seal in it as shown in the picture or the other green part
Sheptack
Reviewed in the United States on August 29, 2019
The Solas Impeller is much better than the stock one, and is a nice upgrade from stock. I have 2 identical Sea-Doos and the hole shot is definitely way better in a real life side by side comparison. The impeller removal tool worked great, and you can use a standard 1/2 drive socket on the head of it. Just remember you will also need a 12mm Allen head wrench, or socket to hold back on the other side of the impeller to remove it/install it. Also note 12mm is an odd size, and most sets only go up to 10mm, and for leverage reasons, I suggest getting a 1/2 drive allen head 12mm socket. Then use 2 breaker bars. Be sure to get the specified bearing grease, and spline grease as well. For whatever reason the wear ring O.D. was way to small (lots of slop, way to much to make up with any filler), also note that my stock model pump housing had 4 set screws apparently to keep the ring from spinning. 2 are real hard to see, and you have to slide off part of the housing to get to 2 of them, but trust me there is 4 total, and if you don't remove them, you will never get the old ring out. My 2004 Sea-doo GTX 4tec Wake called for an OEM ring 267000419. Seller sent me another one of the same rings, and also did not fit. Beware if you have my make and model as the supplied Titan Wear ring did not work for me, and I have a stock pump housing. Seller gladly refunded my money for the wear ring, and sent me labels to return the 2 rings. Great seller, friendly, and easy to deal with. When I am ready to get the Solas Impeller for my other Sea-doo, I will order it from them.
Zach H.
Reviewed in the United States on July 1, 2019
Fit perfectly on my sea Doo rxp 2007! Now it runs like a charm!!
Brian Turney
Reviewed in the United States on May 23, 2019
I replace the damaged prop on my Seadoo. This product was just as described and shipping was super fast.
Spatt
Reviewed in the United States on September 25, 2018
Can’t believe what a difference this made in performance. Good quality product.
Mark
Reviewed in the United States on September 14, 2017
After contacting Bay Area Power Sports regarding questions I had for a replacement impeller for my sea doo, I ordered this Solas Impeller. The parts arrived as promised and packaged very securely. The fit was perfect and the instructions provided by Bay Area Power Sports were very helpful during my installation. The fit and finish of the Solas impeller was outstanding. It was a breeze to install the parts and I am thrilled to report my Sea doo is operating back at top performance. I had a great experience with these parts and this seller!
Recommended Products
$337.69
$ 99 .00 $99.00
$284.95
$ 99 .00 $99.00