Your cart is empty.
Your cart is empty.
Specifications
Working voltage: DC12V-24V
Relay load: 5A per channel
Controller: DMX512 3P D
mx512 Data: 0-127 Relay Switch OFF,128-255 Relay Switch ON
Size:120*55*20
Weight: 100g
DIP10 function key (FUN).
DIP10 (FUN) is OFF, as DMX512 mode, receive standard DMX512 signal. Occupies three address code, (R, G, B for each channel), DIP1-DIP9 address code setting.
When less than 127 DMX512 data relay off
DMX512 data is greater than 127 when the relay is closed
DIP10 (FUN) is ON, the built-in change mode and does not receive standard DMX512 signal. DIP1-DIP9 to invoke the built-in effects settings.
Keith Rule
Reviewed in the United States on June 3, 2024
This controller is cheap and easy to set up, but it doesn't work with my application (creating water effects). The issue is that I need to switch 24VAC to control standard sprinkler system values. Everything works well until I connect the 24VAC to the sprinkler through the relay. When the relay closes, the DMX controller locks up. I suspect it's noise. I've tried everything I can think of to isolate the pieces - with no luck. I ended up having to purchase a 4-channel DMX AC switch to successfully make this work.It's a bummer, but sometimes cheap isn't cheaper in the long run.
Bob W
Reviewed in the United States on March 23, 2023
Did exactly what I needed it to do. Works very well. There were no instructions included but having used similar items I got it going. Packaging could be better, was wrapped in thin bubble wrap and put in a Mylar mailer. The component leads had already torn the inner bubble wrap. Luckily there was no damage.
Richard W Buman
Reviewed in the United States on October 6, 2023
Used this to modify a stage telephone ringer (Tele-Q) for operation via DMX. So far, using just one regular channel. But, since there are three relays, I'm planning to go the next step and add the functionality to ring up to three separate phones from the same Tele-Q. Just a note that these relays do make a little noise, if that might be an issue for your application.
James McFarland
Reviewed in the United States on August 13, 2022
I am using it for three specials that are not DMX. Just on and off switch. But it works flawlessly.
Andrea Tabone
Reviewed in Italy on November 4, 2022
Montate 3 schede per automatizzare effetti in dmx. Tutto ok.Peccato solo perché non ha il DMX out (link)
nico
Reviewed in France on January 22, 2022
Très pratique, fonctionne bien, je vais en acheter un second. Il n'est plus indispensable d'acheter des gradateurs pour piloter des petits lights en dmx. Cette carte est franchement moins chère que des boitiers tout prêts à 100-150 euros qui ne peuvent piloter que 4A. Cette carte a des relais 10A et même si c'est une chinoiserie, pour l'instant elle tient bon.
Novais
Reviewed in the United States on April 29, 2022
Perfect for our application. Item exactly as shown. We're controlling 5 LED key lights in our church. Perfect sync and time response.
Rudy Bruijns
Reviewed in the Netherlands on January 14, 2021
Dik tevreden over dit artikel. Fijn en simpel ook voor stand alone goed te gebruiken.
BADGRRL
Reviewed in the United States on February 4, 2020
There's not much else to say. Package came in quickly and unit works perfectly right out of the box. Instructions are clear, used it to control an old fog machine by taking apart the remote momentary switch and wiring it to the relay contact terminals. I now have a fog machine that accepts DMX control via relay switch. You need very minimal wiring knowledge to work with this unit and I'd recommend finding an enclosure to keep contacts from crossing paths.
藤井大輔
Reviewed in Japan on June 10, 2019
長時間テストはしておりませんが，ちゃんと機能することを確認しました．接続の要領としては，1. DMX512の回路を入力側に接続: 1=GND, 2=COLD, 3=HOT2. DIPスイッチでDMXチャネル番号を設定: DIP#1=ON(残りOFF)でCH#1 ←具体的な設定方法が説明書きだけではわかりにくい．ネット検索すれば同様の設定が出てきます．3. V+,V-に12V以上の電源を接続: リレーは10V～で動作を確認しました．4. DMXコントローラ側で，設定したチャネルのディマーを上げ下げします．5. 3つの回路が設定CH(これをaとします)，a+1，a+2 のチャネルでON/OFF: ・ディマー0～127=OFF，128～255=ONリレーが「カチッ」といって動作するのを確認しました．リレーを使うメリットですが，入力するDMX側(多くは7Vp-p程度のシリアル信号)と電気的に離れている(完全かどうかは怪しい．入力電源が1つなので)ために，駆動される回路側でショート等が起きたとしても，DMXの回線には影響がありません．注意するべきことは，2点です．a. DMXディマーの値の変化に対して127/128を境にしてON/OFFのみ，ということです．リレーなので当然ですが．b. リレーの駆動電圧が12V～です．たとえば12Vバッテリーの自動車で使う場合，バッテリーあるいはオルタネータがへたってきた時に，動作が不安定になる可能性がある，ということです．測定では10Vで動きましたが，あくまでも可動域の補償範囲は12V以上ですので，ご注意ください．製品としてはちゃんと動いているのですが，上記のようなちゃんとした解説をつけて頂きたいところです．
Reflex
Reviewed in the United States on June 13, 2018
Easy DMX control (on/off). I own several of these to fire off pyro, lights, and sound effects. They only turn on/off - they will not dim your lights. Once the DMX value reaches 128, the relay turns on.Side note - You can rewire these to be N.C. (normally closed) switches. You just have to find the alternate solder connection on the board. DMX will then turn a light off instead of on. Great for Haunted House applications.
JimJoiner
Reviewed in the United States on May 11, 2018
I am using this as the basis to control a Kodak Carousel projector remotely using QLC+ for a High School Theatre group and so far, it has worked perfectly. I can advance the slides and turn the lamp on/off as needed. Although you can power it using a 9V battery, It will drain the battery pretty quickly so I would recommend using a 12v Power Supply. If you want to use this, I would also suggest that you plan on building a case for it (access to a 3D printer) and be able to wire it. The documentation is pretty sparse but is adequate if you are familiar with DMX and Relays. Although they give you the mounting hole locations, I really would have liked a board layout with the location of the LEDs. Finally, although you can buy the same board from China for a little bit cheaper, I think they are charging a fair price and was able to get the board in a couple of days.
JORDI M.
Reviewed in Spain on January 7, 2016
Cumple con su función a la perfección. Tan solo basta tener una fuente de alimentación de 12-24v. Se echa en falta algo que identifique los pares de los relees, por lo demás funciona sin problemas. Una gran compra a un precio inmejorable.
Recommended Products
