Shopping Cart

Your cart is empty.

Your cart is empty.

DEF Rev Counter Board RVCTBD50 for Mighty Mule FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Series (2)

Free shipping on orders over $29.99

$14.99

$ 7 .99 $7.99

In Stock

About this item

  • Composition: Consists of a tachometer and a limit switch to prevent your gate arm from running off
  • Suitable for: FM350 FM352 FM500 FM502 FM600 2000XL MM500/502 Mighty Mule,GTO PRO 2500 series
  • Determine the location of the fault: If the main arm fails, you will hear 3 beeps, if the secondary arm fails, you will hear 4 beeps, you need to pay attention to check the circuit board now and replace it in time
  • Waterproof coating: surface gel coating to refuse the erosion of moisture, enhance the practical cycle, do not have to worry about the impact of fog, rain, snow or heat and humidity, so you can easily drive into the home
  • Save money: it is very difficult to find professional repair personnel engaged in these devices, now you can DIY to solve the main arm failure problem, which is very simple and saves you money


Product Details
Item Weight: 0.81 ounces
Package Dimensions: 3.7 x 3.1 x 1.1 inches
Item Package Quantity: 1
Batteries Included?: No
Batteries Required?: No
We strive to provide easy-to-understand content to eliminate confusion when purchasing products
We cut through the version confusion to help you find the right replacement part for your needs
We take the extra step to make sure you get the right product for your project
The parts we sell are designed for all specific generations of gate openers
Installation Steps:
1 First, you must turn off the power switch on the lower left side of the control box.
2Remove the cotter pins at the ends of the gate arms. Leaving all the wiring in place, you turn the gate arm upside down and
place it on a piece of cardboard on the floor. Then use the T20 tool head to remove the 14 screws. Less than 2 minutes with a battery operated tool.
3 You open the clamshell housing an inch or so and unplug the pin connector cable. Note that the cover does not come off, but rotates open.
4 A shorter T20 screw holds the board to the assembly, screw the new board on, and then reinsert the connector,
Make sure the orange and green cables match the markings on the board.
5 After getting all this accumulated junk out, it's a good idea to put some wire or small nails in the drainage holes on the bottom,
to make sure the water can drain out.
6 Put the arm back together, lubricate all the pins and friction points with molybdenum grease, and then turn the power back on.

Note: There is no manual


Kel
Reviewed in Canada on March 10, 2024
I liked that they work.
Marcia
Reviewed in the United States on April 7, 2024
Nice and easy replacement parts.
Bob
Reviewed in the United States on August 2, 2022
Lever on switch stopped working after 5 or 6 cycles.
Anderson Henry
Reviewed in the United States on November 28, 2022
Product works well after months in service.
Ed Conti
Reviewed in the United States on October 12, 2022
Find a different seller! Because of non-existent quality control both boards were incorrectly cut and would not fit without modification, one did not work at all, second one quit after ONE day! Contacted seller and received no response. This bargain was no bargain, junk.
DW
Reviewed in the United States on November 25, 2021
Pack of 2. The first one lasted about 6 weeks, the second one didn’t work for a day. Ended up purchasing the brand name Mighty Mule and my gate is back to working like a charm. Tried to save some money and it ended up costing me double. Live and learn right….
Recommended Products

$10.99

$ 5 .99 $5.99

4.6
Select Option

$19.99

$ 8 .99 $8.99

4.7
Select Option