Your cart is empty.
Your cart is empty.Product Description
VCELINK RJ45 Pass Through Multi Modular Dovetail clip Crimper
Multi Function：
Used for pass through design connectors , crimp the connector and cut the extra wires , another function of crimping dovetail clip, which is helpful for crimping modular plugs with feed-thru design and dovetail clip at the same time
High Precision：
High-standard precision crimping and grinding port, fixed modular plugs to make sure cables do not fall
Built-in Cat7 to Cat5 Switcher
Switch from Cat7 to Cat5 crimping by using a screwdriver to loosen then switch up or down to change the compression mode.
- The Cat7 mode stands for Cat7 and Cat6a shielded plugs crimping.
- Cat5 mode stands for Cat5, Cat5e and Cat6 plugs crimping.
Built for Pass-thru Network Connectors
- Crimps RJ45 (Data) and RJ12 RJ11 (Voice) fixed die cavities, supports Cat5 Cat5e Cat6 Cat7 Ethernet STP/UTP cables, twisted pairs, phone, voice and data cables crimping.
Built for Dovetail Clip
- Specially design for Cat6a Cat7 shielded connectors and even crimp the metal clip on the plugs.
Compact Design Modular Crimper
- One hand operation with rust resistant blue oxide coated steel core.
- The compact size fits in any pocket, tool pouch.
- Recoil spring loaded ergonomic matte handle returns tool to ready position upon cycle completion helps you save time and effort.
What You Get:
20 x Cat6A RJ45 Pass-Through Connectors
20 x RJ45 Anti-Twist Protectors
1 x GJ671BL RJ45 Crimping Tool
1 x RJ45 Cable Tester
1 x Mini Wire Stripper
1 x Wire Cutter
1 x Punch down impact tool
2 x GJ671BL Replacement Blades
1 x Fabric Storage Bag
Jacob
Reviewed in the United States on May 6, 2025
Great product.
JeanChri
Reviewed in France on May 12, 2025
Je ne suis pas un spécialiste mais j’ai pu monter mes prises avec ces outils. Ils font le job.
DaniNe
Reviewed in the United States on March 25, 2025
Cumple su funcion hice un par de cables y los comprobe y no me ha dado ningun problemas hasta ahora!!!
yang li
Reviewed in the United States on March 2, 2025
The crimping tool is well built and easy to use. The only downside is the design of the lock button. It works pretty well at beginning. After sitting for several months without using, the button stucked and it is really hard to unlock it.
Jo
Reviewed in the United States on April 17, 2025
Does what it says it will do
FranJFK
Reviewed in Spain on September 12, 2024
He estado montando una red por casa y aunque no he usado el medidor de señal, el resto si que le he dado uso y la verdad que ha funcionado de maravilla para el uso que necesito darle que no es profesional ni un uso muy comedido.
Aaron
Reviewed in the United States on March 13, 2024
I waited to review to make sure these weren’t two week junk. I’m a low voltage tech and my company does a LOT of Crestron automation systems. I use these daily and I’m impressed. They’re holding up and crimping just as well as my Kleins if not better!
Mir ishfaq
Reviewed in India on February 17, 2024
I used it couple of times and worked like a dream. Color and built quality is undoubtedly of next level💪
Curtis Brown
Reviewed in the United States on October 4, 2024
The crimping tool works well. I like the pass through connectors. Having terminated many cables before, I can definitely say the pass through connectors make it easier.
Snibby
Reviewed in the United States on September 15, 2023
I was surprised to find it works well on not just pass through connectors but on conventional closed end connectors for CAT6, CAT5E. I had to terminate an outdoor Access Point run at a hospital. It uses a shielded CAT6 with UV resistant cover, which is always a bear to terminate with a pass-through Rj45 supplied by the cable supplier. The tool worked great. The vendor supplied silicone rubber clear gue to place at the end of connector before sliding on boot to seal the connection required at each end to prevent water vapor from entering the cable run. I had to make a patch cable inside with conventional cable, I found the tool can terminate non-pass-through connectors easily. I probably use 100 connectors a month. I always use CAT6 for 10G on runs less than 40 feet except where bundle with 50 or more. 10G always use CAT7 shielded on >100 foot runs, and on any bundle run. I also charge 5 times cost for termination because it takes a long time to terminate CAT7 compared to CAT5E. Surprised the inexpensive tool works well in all situations.
Customer
Reviewed in Canada on August 22, 2023
Works as intended.
Xavier
Reviewed in Mexico on December 30, 2023
El pedido llego en tiempo y forma, el paquete llego tal cual se ven las imágenes en la pagina, envío seguro y en tiempo y forma. El producto se ve bien estoy satisfecho con la compra, no le he usado todavia.
Spammy Hagar
Reviewed in the United States on November 2, 2023
I initially bought these because I saw they had a strain relief crimping section for crimping strain relief tabs on cat6a/cat7 cables.The RJ45 crimping part works great for crimping through-hole cat6a and cat7 cable connectors. It usually trims the ends of the through-hole jacks cleanly in one or 2 passes, tops.The strain relief crimping section however, never seems to line up correctly (at least for fatter cat6a & cat7 cables).With cat6a+, you end up having to "pre-crimp" the strain relief tabs around the cable, then clock the cable in the crimper in such a way that it is offset in the die in which it was designed to sit when crimping.If you just let the connector sit in the strain relief crimping die the way it was intended to be used, and squeeze, it smashes the tabs flat on the side of the cable, and not around the cable the way they were intended to be crimped. That's why I gave 4 starts instead of 5.They do work well once you get the hang of how you have to hold them for crimping big cable strain reliefs, and that is my only gripe about them.
Recommended Products