Your cart is empty.
Your cart is empty.Product Description
Time to upgrade your existing pellet grills up to speed by this new PID Gen 2 control board.
Perfectly compatible with Camp Chef grill（including models of Pursuit 20, SG24, SG 30, SGX, DLX, XT, smokePro DLX 24, SmokePro LUX 36, SmokePro STX 24, SmokePro XT 24, Woodwind Classic 24 (PG24STX, PG24XT, PG24S, PG24WWS)NOT XXL Vertical Smoker).
Allowing you to control the smoke intensity to your preference, creating perfect smoky flavor for your grilled time. This replacement retrofit controller would be your best grilling helper.
Product Features
2 PID Programs and Bypass Mode
- 2 PID programs for more consistent temperature，Code: 300 for small grill models SG 24 and pursuit 20, Code: 600 for the other big grill model.
- Bypass mode to skip normal startup and get the grill cooking again quickly.
Handy Navigating Knob and Big Bright Screen
- Larger, high-visibility, low-glare digital display screen.
- Handy smoothy dialing knob to navigate through setting menu easily.
Fun Cook
- Change the smoke intensity by 10 smoke options from 160F-350F.
- Wide temperature range: 160°F/71°C-500°F/260°C.
CAUTION
- Always start the grill with the lid open. The lid must be colesed after the start cycle.
- Do not over-fire the grill by over feeding pellets into the burner prior to startup.
- If flame is inadvertently extinguished never restar the grill wihout first cleaning out the burner. Improper use can cause an uncontrolled fire.
- Do not turn the main power switch off while the grill is hot.
Specification
- Color: Black
- Voltage: AC 120V
- Input: AC 120V 60Hz(PIN 1~4)
- Output: AC 7.5V 200mA(PIN 5~8)
- Size(L*W): 20.3 x 8 cm/8" x 3.15"
- Temp Range: 160°F/71°C-500°F/260°C
Brittni Snow
Reviewed in the United States on May 23, 2025
Worked perfect
Denise Hanson
Reviewed in the United States on May 19, 2025
It doesn't work at all. I ran my grill for about 2 hrs set to 325 and it never once got up to temp. The fan would not kick on at all. I understand that it says that the fan will kick off when it gets up to temp, but like I said it never got up to temp. The only time the fan would kick on is when I changed the temp setting. It would run for roughly 10 seconds and then completely stop.
Shawn
Reviewed in the United States on January 26, 2025
Easy to install and works great
Britt Bush
Reviewed in the United States on April 27, 2025
Works as expected!
Stephen S.
Reviewed in the United States on September 8, 2024
This was easy to replace and works great. It does turn the fan off and on unlike the original but does hold the temperature very well and the shutdown cycle works great.
Shaun
Reviewed in the United States on July 18, 2024
My original unit was WIFI, this is not. I was aware before buying, but the Camp Chef app was garbage anyway. The stock panel knob failed. This one feels more solid. The cycling is different: the blower fan turns off completely when at temp. I found that I use far less pellets, my assumption is they burn slower without the fan. Temperature is also more stable. Setup was a bit of a chore, the wires at first seemed to be the wrong color, and difficult figure out. I found that my old wires were discolored. Looking under a zip tie, I could see they were a match. I recommend swapping wire connectors one at a time to avoid confusion. One socket is in a different spot on the card. Other than initial installation confusion, it works better than the stock panel, if you can live without WIFI, this is a great unit.
Short Circuited Brewers
Reviewed in the United States on February 8, 2024
Just got mine installed and it was an easy install. The only thing to be aware of is. The fan will cycle if you use a temperature setting with a smoke setting. The PID tries to regulate the temp by cycling the fan on and off. THIS IS NORMAL. It is how it controls the heat from the pellets. If you use a "Low smoke" or "High Smoke" setting the fan will run continuously. Just so everyone knows it is not a bad controller if this happens.
Richard R
Reviewed in the United States on October 25, 2023
First one wouldn’t provide enough power to hot rod to fire off pellets. Seller replaced it cross-shipped so I was back in business 2 days later. The 2nd one works fine so far and it seems to hold temps as well,or maybe slightly better than OEM controller
Recommended Products
$30.49
$ 14 .99 $14.99